Yarn and knitting
Crochet Hook Size Chart
Choose a hook size in millimeters. You get its US letter and number, the yarn weights the standard pairs it with, and the knitting needle of the same size.
Published Nov 19, 2026
Worked example
- The millimeter size is the diameter of the shaft, where the loops sit; it is the number to trust
- US hooks carry a letter and usually a number too; the letters are not used the same way by every maker above about 9 mm
- A 5 mm hook is in the range the yarn standard gives for light yarn
- If your swatch has too many stitches per 4 in, go up a hook size; too few, go down
Crochet hook sizes
| Millimeters | US size | Yarn weight |
|---|---|---|
| 2.25 mm | B-1 | 0 lace, 1 super fine |
| 2.75 mm | C-2 | 1 super fine |
| 3.25 mm | D-3 | 1 super fine |
| 3.5 mm | E-4 | 1 super fine, 2 fine |
| 3.75 mm | F-5 | 2 fine |
| 4 mm | G-6 | 2 fine |
| 4.5 mm | 7 | 2 fine, 3 light |
| 5 mm | H-8 | 3 light |
| 5.5 mm | I-9 | 3 light, 4 medium |
| 6 mm | J-10 | 4 medium |
| 6.5 mm | K-10½ | 4 medium, 5 bulky |
| 8 mm | L-11 | 5 bulky |
| 9 mm | M/N-13 | 5 bulky, 6 super bulky |
| 10 mm | N/P-15 | 6 super bulky |
| 15 mm | P/Q | 6 super bulky, 7 jumbo |
| 16 mm | Q | 7 jumbo |
| 19 mm | S | 7 jumbo |
Steel hooks (for thread)
| Steel hook | Rule |
|---|---|
| Small numbers (00, 0, 1) | the largest steel hooks |
| Large numbers (10, 12, 14) | the smallest; a higher number is a finer hook |
| Used with | crochet thread and lace weight yarn |
Steel hook numbers run the opposite way to the letters: the higher the number, the smaller the hook. Check the millimeter size printed on the hook.
Millimeters are the real size
A crochet hook's size is the diameter of its shaft, the part where the loops sit and get their size. That measurement in millimeters is the number to trust, because a millimeter means the same thing in every country and on every pattern.
The US system puts a letter in front, usually with a number as well: B-1 is 2.25 mm, H-8 is 5 mm, K-10½ is 6.5 mm. The letters run in order up to about 9 mm, and above that makers do not use them the same way. A 9 mm hook may be labeled M/N-13 or M-13, and 10 mm N/P-15 or N-15. Go by the millimeters whenever the letter and the pattern disagree.
Gaps and odd sizes in the chart
A few sizes have only a number. The 4.5 mm hook is simply a 7, sitting between G-6 at 4 mm and H-8 at 5 mm. At the big end the steps get large: L-11 is 8 mm, then 9, 10, 15, 16 and 19 mm. The Q hook is listed at 16 mm and also at 15.75 mm, so the two are the same tool.
Hooks of 15 mm and up are used with jumbo yarn, category 7, and the smallest in the main chart, B-1, overlaps with lace and super fine yarn.
Steel hooks run backward
Hooks finer than about 2 mm are steel hooks, made for crochet thread and lace. Their numbers run the opposite way: the higher the number, the smaller the hook. A size 10 steel hook is 1.3 mm. Charts disagree on several other steel sizes, so read the millimeter size stamped on the hook rather than a conversion table.
Choosing a hook for your yarn
The yarn weight column follows the hook ranges in the yarn standard. Medium (worsted) yarn, category 4, pairs with 5.5 to 6.5 mm hooks, I-9 to K-10½. Light yarn, category 3, pairs with 4.5 to 5.5 mm. The full ranges are on the yarn weight chart.
The range is a starting point. Crochet a swatch and count the stitches in 4 in. If you have too many, your stitches are small: go up a hook size. Too few, go down one. The gauge calculator does the counting math, and the crochet blanket size chart turns your gauge into a foundation chain.
Hooks and needles share sizes
Because both are measured by diameter, a 5 mm hook and a 5 mm knitting needle are the same thickness, even though one is called H-8 and the other US 8. The knitting needle size chart lists the needle names.
Questions
What size is an H crochet hook?
An H-8 hook is 5 mm. The standard pairs it with light yarn, category 3.
What size hook for worsted weight yarn?
Worsted is medium yarn, category 4, and the standard gives 5.5 to 6.5 mm hooks, I-9 to K-10½.
Do steel hook numbers work like letter hooks?
No. Steel hook numbers run the other way: a higher number is a smaller hook. A size 10 steel hook is 1.3 mm.
Why do two 9 mm hooks have different letters?
Above about 9 mm makers do not use the letters the same way, so a 9 mm hook can be M/N-13 or M-13. The millimeter size is the reliable one.
How we calculate: every rule and rounding step is on our method page; where the sizes and facts come from is on sources.
broiderer.com is not affiliated with any fabric, thread or sewing machine brand. Last reviewed November 2026.