Quilt calculators
Quilt binding calculator
Type the finished quilt size, the width you cut your binding strips and the usable width of your fabric. You get the total binding length, the number of strips and the yardage, rounded up so you never come up short at the last corner.
Published Nov 1, 2026
Worked example
- Perimeter: 2 × (90 + 95) = 370 in, plus 12 in for corners and the final join = 382 in
- Each strip gives about 42 − 2½ = 39½ in after the diagonal joins
- 382 ÷ 39½ = 9.67, rounded up to 10 strips
- 10 × 2½ in = 25 in of fabric = ¾ yd
Binding for common quilt sizes (2½ in strips, 42 in fabric)
| Quilt | Size | Binding length | Strips | Fabric |
|---|---|---|---|---|
| Crib | 36 × 52 in | 188 in | 5 | ⅜ yd |
| Lap | 50 × 60 in | 232 in | 6 | ½ yd |
| Twin | 68 × 90 in | 328 in | 9 | ⅝ yd |
| Full | 84 × 90 in | 360 in | 10 | ¾ yd |
| Queen | 90 × 95 in | 382 in | 10 | ¾ yd |
| King | 106 × 95 in | 414 in | 11 | ⅞ yd |
Strip width and finished binding
| Cut strip | Folded (double fold) | Finished width on the front | Best for |
|---|---|---|---|
| 2 in | 1 in | about ⅜ in | thin batting, small quilts |
| 2¼ in | 1⅛ in | about ⅜ in | cotton batting |
| 2½ in | 1¼ in | about ½ in | most bed quilts |
| 2¾ in | 1⅜ in | about ½ in | thick or wool batting |
Where the 12 extra inches go
The perimeter is only the starting point. Every mitered corner folds a little binding into itself, and the two loose ends need room to overlap and join where you started. Published guides add anything from 10 to 20 in for this; the calculator uses 12 in, which is why the queen example asks for 382 in rather than the bare 370 in around the edge.
If you like to leave a long tail before you start stitching, or your quilt has many corners, type a slightly larger quilt size so the length goes up.
Why a 42 in strip only counts as 39½ in
Strips are joined end to end with diagonal seams, because a 45 degree join spreads the bulk out instead of stacking it in one lump on the fold. Each diagonal join eats about one strip width, so a 42 in strip of 2½ in binding adds about 39½ in to the length. That is the number the calculator divides by: 382 ÷ 39½ = 9.67, rounded up to 10 strips.
Ten strips at 2½ in use 25 in of fabric, which comes to ¾ yd. A lap quilt works the same way: 2 × (50 + 60) + 12 = 232 in, ÷ 39½ = 5.87, so 6 strips and 15 in of fabric, or ½ yd once rounded to a cut you can buy.
Picking the strip width
Double-fold binding is cut at 2¼ or 2½ in by most quilters, with 2½ in the most common. The fold halves the strip, and part of it wraps around the batting, so the finished width on the front ends up around ⅜ to ½ in. A thick wool or puffy batting takes up more of the wrap, which is why the table above suggests 2¾ in for those. A narrow 2 in strip suits thin batting and small pieces such as mug rugs and table runners.
Sew a short test length on a scrap sandwich of the same batting before you cut everything. If the fold does not reach your stitching line on the back, go up ¼ in.
Straight grain or bias
For a quilt with straight sides and square corners, strips cut across the width of fabric are the usual choice and use the least cloth. Scalloped or rounded edges are different: a strip cut at 45 degrees to the grain has the most stretch and bends around a curve without puckering. Use the bias tape calculator to find the square that gives you enough continuous bias.
Striped fabric is a matter of looks. Cut across the width, the stripes run straight along the binding; cut on the bias, they turn into a barber-pole stripe.
Before you cut
Measure the quilt after quilting and trimming, not the pattern size, since quilting draws the top in. Then cut, join and press the strips in half lengthwise. If you are still planning the rest of the quilt, the quilt fabric calculator gives top, backing and binding in one list.
Questions
How wide should I cut quilt binding strips?
2½ in is the most common cut for double-fold binding on bed quilts, and 2¼ in is the narrower traditional choice. Go up to 2¾ in for thick batting.
How much binding do I need for a queen quilt?
A 90 × 95 in queen quilt needs about 382 in of binding: 10 strips of 2½ in cut from ¾ yd of 42 in fabric.
How many binding strips for a twin quilt?
A 68 × 90 in twin needs 328 in of binding, which is 9 strips of 2½ in, or ⅝ yd of fabric.
Do I need bias binding for a quilt?
Only for curved or scalloped edges. Straight edges take strips cut across the width of fabric.
How we calculate: every rule and rounding step is on our method page; where the sizes and facts come from is on sources.
broiderer.com is not affiliated with any fabric, thread or sewing machine brand. Last reviewed November 2026.