Skip to content
broiderer

Fabric

Fabric widths

Type the width on the bolt, how much you trim off for selvages, and the size of the piece you cut across the strip. You get the usable width, how many pieces fit in one strip, and what is left over.

Published Nov 1, 2026

Your numbers

runs in your browser, nothing is saved

Usable width
43 in
6½ in pieces per strip6
Left over per strip4 in

Typical values. Widths and weights vary by mill; check the bolt or the listing.

Worked example

  1. Bolt width 44 in − 1 in of selvage = 43 in
  2. 43 ÷ 6½ = 6.62, so 6 whole pieces
  3. Plan with the usable width, not the label: a few inches of shrinkage or a wide selvage can cost you a piece per strip

Typical fabric widths

FabricWidthNote
Quilting cotton42 to 44 in40 to 42 in usable after trimming selvages
Wide backing108 inalso sold at 90, 118 and 120 in
Apparel fabric45, 54 or 58 to 60 in36 in is an older width still sold
Home decor54 inrange 54 to 60 in
Fleece58 to 60 inoften labeled 58/60
Muslin36 to 120 inthe wide widths are for backings and theater sets

Widths printed on the bolt are before washing. Prewashed cotton can lose another inch or two.

Pieces per strip at 40 and 42 in usable width

Cut piece40 in42 in54 in58 in
2½ in16162123
3½ in11121516
4½ in891212
5 in881011
6½ in6688
8½ in4466
10½ in3455
12½ in3344

Label width versus usable width

The width printed on the bolt includes both selvages, the finished edges along each side, which often carry printing. You trim them off before cutting, so what you can actually use is narrower. Quilting cotton labeled 42 to 44 in usually leaves 40 to 42 in.

In the example, 44 in minus 1 in of selvage leaves 43 in. Pieces of 6½ in fit 6 times, because 43 ÷ 6½ = 6.62, and the last 4 in becomes scrap. If that strip had been 45½ in wide you would have squeezed in a seventh piece, which is why the calculator starts from the width you measured, not the label.

Why patterns use 40 or 42 in

Pattern writers do not know which bolt you will buy, so most plan quilting cotton at 40 in, sometimes 42 in. The lower number is the safe one. Look at the second table: 3½ in pieces fit 11 times at 40 in and 12 at 42 in, so a quilt with 120 of them needs 11 strips at the safe width and only 10 at the generous one. When you prewash, cotton can lose another inch or two across the width, so measure after washing.

The table also shows wider goods. A 5 in square fits 10 times across 54 in decor fabric and 11 times across 58 in fleece.

Wide backing and when it helps

Backing fabric made for quilts is most often 108 in wide, with 90, 118 and 120 in also sold. It lets you back a large quilt in one piece. For a quilt 90 in wide that will be quilted on a longarm, you add about 4 in on each side, so you need at least 98 in of width. From 42 in cotton that means seaming three widths together. One length of 108 in backing covers it with room to spare. The quilt backing calculator works this out for any size.

Apparel and home decor widths

Garment fabrics come most often at 45 or 60 in, and you will also see 54 and 58 in. Some 36 in fabric is still sold. Decor fabric for curtains, cushions and table linens is usually 54 in and can reach 60 in. Muslin covers the widest spread, from 36 to 120 in, and the wide widths go to quilt backings and theater sets.

Wider fabric needs less length for the same project, but only if your pieces fit across it well. Always check how the pieces lay out before you convert yardage from one width to another.

Grain and cutting across the width

Strips cut across the width run on the crosswise grain, which stretches a little more than the lengthwise grain parallel to the selvage. For most patchwork that is fine. For borders that must stay flat, some quilters cut along the length instead. See how much fabric is in a yard for what one yard of each width gives.

Questions

What is the standard width of quilting cotton?

42 to 44 in on the bolt, with about 40 to 42 in usable after the selvages are trimmed.

How wide is wide quilt backing?

Most often 108 in. It is also sold at 90, 118 and 120 in.

Why does my fabric measure narrower than the label?

The label includes the selvages and is measured before washing. Trimming the selvages and prewashing can each take off an inch or more.

What width is fleece?

Usually 58 to 60 in, often labeled 58/60.

How we calculate: every rule and rounding step is on our method page; where the sizes and facts come from is on sources.

broiderer.com is not affiliated with any fabric, thread or sewing machine brand. Last reviewed November 2026.