Skip to content
broiderer

Table and bed

Placemat Size

Enter the finished placemat width and length and how many you want. You get the cut size for fronts and backs, the fabric for each, the batting pieces, and the binding if you bind the edges instead of turning them.

Published Nov 16, 2026

Your numbers

runs in your browser, nothing is saved

Cut size, front and back
12½ × 18½ in
Front fabric¾ yd
Back fabric¾ yd
Batting4 pieces at 13 × 19 in
Binding instead of turning280 in of 2¼ in strips

Typical sizes; brands differ. Measure your table, pillow or bed.

Worked example

  1. Add ¼ in seam on every side: 12 + ½ = 12½, 18 + ½ = 18½ in
  2. A 42 in strip 12½ in tall holds 2
  3. 4 placemats: 2 strips = ¾ yd for the fronts, the same for the backs

Placemat sizes

ShapeSize
Rectangle (most common)12 × 18 in
Rectangle or oval13 × 19 in
Large rectangle14 × 20 in
Round12 to 15 in across
Square13 or 14 in

The sizes, and why 12 × 18 in wins

The most common rectangular placemat is 12 × 18 in. It holds a dinner plate, a glass and the flatware on either side without crowding the next seat. Quilted and oval mats are often a little bigger at 13 × 19 in, and a large rectangle is 14 × 20 in. Round placemats run 12 to 15 in across, and square ones are 13 or 14 in.

Check your table before you pick a size. Two 12 in deep mats facing each other across a 36 in table leave 12 in down the middle, about right for a serving dish or a table runner a third of the table's width. On a narrower table, the larger sizes start to touch.

Cutting fronts and backs

For a turned placemat, the front and back are each cut ½ in larger than finished in both directions, a ¼ in seam on every side: 12½ × 18½ in. From 42 in fabric, cut a strip 12½ in tall across the width and you get two fronts from it, since two 18½ in pieces take 37 in. Four placemats need two strips, 25 in of fabric, so buy ¾ yd. The backs need the same again.

Cut this way, the lengthwise grain runs along each mat's 12½ in side, so a one-way print that runs parallel to the selvage stands upright when you look at the mat from your seat. If your print runs the other way, cut 18½ in strips instead and check the yardage again.

Turned edges or binding

There are two ways to finish. Turned: layer batting, then the back and front right sides together, sew all round with a ¼ in seam, leaving a gap on one long side, trim the corners, turn, press, and topstitch close to the edge to close the gap. The batting pieces are cut 13 × 19 in and trimmed to the seam after sewing.

Bound: layer the front, batting and back wrong sides together, quilt them, trim to 12 × 18 in, and bind like a small quilt. Four mats need 280 in of 2¼ in binding strips, the 60 in edge of each mat plus about 10 in for joining. From 42 in fabric that is seven strips. The quilt binding calculator shows the method in full.

Small things that make mats last

  • Prewash all fabrics. Placemats are washed often, and a front that shrinks more than the back makes the mat cup.
  • Use thin batting so glasses stand level.
  • Quilt lines no more than a few inches apart, so the layers stay together through washing.
  • Press after turning, rolling the seam to the edge with your fingers before the iron touches it.

Questions

What is the standard placemat size?

12 × 18 in is the most common. 13 × 19 in and 14 × 20 in are also sold.

How much fabric do I need for 4 placemats?

For 12 × 18 in mats, ¾ yd of 42 in fabric for the fronts and ¾ yd for the backs.

What size is a round placemat?

Round placemats are usually 12 to 15 in across.

Should I bind or turn the edges?

Turning is quicker and leaves no visible binding. Binding gives a crisp framed edge and suits a quilted mat.

How we calculate: every rule and rounding step is on our method page; where the sizes and facts come from is on sources.

broiderer.com is not affiliated with any fabric, thread or sewing machine brand. Last reviewed November 2026.