Skip to content
broiderer

Table and bed

Table Runner Size

Type your table's length and width and how far you want the runner to hang past each end. You get the finished runner size and the two pieces to cut for a lined runner.

Published Nov 4, 2026

Your numbers

runs in your browser, nothing is saved

Runner
12 × 84 in
Length84 in
Width12 in (about a third of the table)
To sew (½ in seams, lined)cut 2 at 13 × 85 in

Typical sizes; brands differ. Measure your table, pillow or bed.

Worked example

  1. Length: table 72 + 2 × 6 overhang = 84 in
  2. Width: about a third of 36 in = 12; runners are usually 12 to 16 in
  3. A lined runner is a front and a back sewn right sides together, turned, and pressed

Runner length by table

Table6 in overhang12 in overhang
48 in long60 in72 in
60 in long72 in84 in
72 in long84 in96 in
84 in long96 in108 in
96 in long108 in120 in
108 in long120 in132 in

Length: the table plus two overhangs

A runner hangs off both ends, so you add the overhang twice. The everyday rule is 6 in at each end, which makes the runner 12 in longer than the table: 72 + 12 = 84 in. For a dressier look some people let it hang 10 to 12 in at each end, so the 12 in column of the chart is there for holidays and parties.

If your table has a tablecloth under the runner, measure the table itself, not the cloth. The runner should hang a little shorter than the cloth's drop, or the two edges fight each other. With a cloth that drops 8 in, a 6 in overhang leaves a clean 2 in step.

Width: about a third of the table

Runners are usually 12 to 16 in wide, with 13 to 14 in the most common. The calculator starts from a third of your table's width: 12 in for a 36 in table, 14 in for a 42 in table. That leaves room on both sides for plates. If you also use placemats, two 12 in deep mats facing each other leave 12 in down the middle of a 36 in table, which is exactly the space a 12 in runner fills. See the placemat size page for mat sizes.

Cutting a lined runner

A lined runner is two layers, a front and a back, sewn right sides together with ½ in seams, turned through a gap, and pressed. Each piece is cut 1 in bigger than the finished size each way, so the 12 × 84 in runner needs two pieces at 13 × 85 in. Leave a 4 to 5 in gap in one long side, clip the corners before turning, and close the gap with topstitching all round.

Cut the long pieces along the lengthwise grain, parallel to the selvage. That grain stretches least, so the runner stays straight and does not ripple down the middle. An 85 in cut is a little over 2⅜ yd, and from 42 in fabric you can cut three 13 in strips across, which gives the front, the back, and one spare.

Quilted or pieced runners

A runner is a good small quilt project. Piece the top from blocks, layer it with batting and a backing, quilt it, and bind the edges instead of turning. In that case cut the backing and batting a couple of inches larger than the top and trim after quilting. The quilt binding calculator gives the strips you need for the edge. Keep the batting thin so dishes sit flat.

Questions

How long should a table runner be for a 6 ft table?

A 6 ft table is 72 in long, so the runner is 84 in with a 6 in overhang at each end, or 96 in with 12 in.

Should a table runner hang over the edge?

Usually yes, about 6 in at each end. A runner that stops at the table edge is also fine on a table you want to keep simple.

How wide should a table runner be?

About a third of the table's width, usually 12 to 16 in.

What seam allowance do I use?

The calculator uses ½ in seams for a lined runner. If you piece the top, use the ¼ in quilting seam; the seam allowance page explains the difference.

How we calculate: every rule and rounding step is on our method page; where the sizes and facts come from is on sources.

broiderer.com is not affiliated with any fabric, thread or sewing machine brand. Last reviewed November 2026.