Table and bed
How to make a tie blanket
A tie blanket is two layers of fleece held together by a knotted fringe, with no sewing at all. The four numbered drawings below show it step by step: stack, cut the corners, cut the fringe, tie.
Published Nov 17, 2026
01Lay the two pieces of fleece wrong sides together and smooth them flat. Trim them together so the edges match.
02Cut a 4 in square out of every corner, through both layers.
03Cut the fringe: 4 in deep cuts, 1 in apart, along all four sides and through both layers.
04Tie every top strip to the strip right under it. Finish one side before you start the next.
Key:top layer of fleecebottom layerthis step: cut or knot
What you need
Everything fits on a large table or a clean floor. The only real choice is the fleece: two pieces the same size, usually a print and a solid that goes with it.
- Two pieces of fleece, 2 yd each for a throw
- Sharp fabric scissors, or a rotary cutter and mat
- A long ruler or a tape measure
- A 4 in square of card to mark the corners
How much fleece to buy
Fleece is sold 58 to 60 in wide, so the width is set and you only choose the length. These amounts are for each of the two pieces, with a 4 in fringe:
- Baby, 36 × 36 in center: 1¼ yd
- Lap, 36 × 48 in center: 1⅝ yd
- Throw, 50 × 60 in center: 2 yd
- Twin topper, 50 × 80 in center: 2½ yd
Why the finished blanket is smaller than the fleece
The fringe is cut from the blanket itself, so it comes off every side. Two yards of fleece is 72 in long and about 58 in wide. Take 4 in of fringe off each edge and the part you sleep under is about 50 × 64 in. For any other size, the tie blanket calculator works out the cut size, the yardage and the number of knots.
Baby sizes are listed as sizes only. The American Academy of Pediatrics says nothing should be in the crib but a fitted sheet for babies under 12 months.
Cutting the corners and the fringe
Smooth the two layers flat and trim them together so the edges match all the way around. Then cut a 4 in square out of each corner, through both layers. Without that cut the corner strips would have nothing to tie to, and the corner would bunch up.
Cut the fringe through both layers at once, so every top strip has a partner exactly under it. Strips 1 in wide and 4 in long are the most common; some instructions use 5 in. Lay the ruler across the fleece 4 in from the edge and cut up to it, and the strips all come out the same length.
Two ways to tie the knots
The first way is a double knot: take a top strip and the strip under it, and tie them to each other twice. The second is an overhand knot, tied the way you tie off a balloon: hold the two strips together as one, loop them around a finger and pull the ends through. The double knot lies flatter. The balloon knot is quicker to tie.
Finish one whole side before you start the next, so the layers do not shift while you work. A throw with a 50 × 60 in center and 1 in strips has 220 knots, which is a good reason to sit two or three people around the table.
Other blankets to make
If you would like a sewn blanket with a soft frayed edge, the rag quilt calculator gives the squares and the fabric. For a pieced throw, start from the lap quilt size page.
Questions
How many yards of fleece do I need to make a tie blanket?
For a throw, 2 yd of each of two pieces, 4 yd in all. That gives a center of about 50 × 64 in after a 4 in fringe.
Do you have to sew a tie blanket?
No. The knots hold the two layers together, and fleece does not fray, so the cut fringe is the finished edge.
How wide and how long should the strips be?
1 in wide and 4 in long is the most common. Some instructions use a 5 in fringe.
What knot do you use on a tie blanket?
Either a double knot that ties the top strip to the bottom strip, or an overhand knot made with both strips held together, like tying a balloon.
How we calculate: every rule and rounding step is on our method page; where the sizes and facts come from is on sources.
Step diagrams drawn by broiderer.com.
broiderer.com is not affiliated with any fabric, thread or sewing machine brand. Last reviewed November 2026.