Skip to content
broiderer

Embroidery stitches

Herringbone stitch

Herringbone stitch is a band of long slanted stitches that cross near each end, worked back and forth between two parallel lines. The numbered diagrams below show it step by step.

Published Nov 8, 2026

  1. 1

    01Work between two parallel lines from left to right. Come up at 1 on the bottom line.

  2. 123

    02Go down at 2 on the top line, up to the right, and come up at 3, a short step back to the left on the same line.

  3. 45

    03Cross down to the bottom line: go down at 4, to the right, and come up at 5, a short step back to the left.

  4. 04Repeat top and bottom. The stitches cross near each end and make a band of overlapping crosses.

Key:stitches already madethis stepneedle under the fabric (dashed)

How many strands of floss

StrandsLine it makes
1 strandvery fine lines, lettering, small details
2 strandsfine outlines; the usual choice on 14 count fabric
3 strandsmedium lines, most surface embroidery
4 to 6 strandsbold lines and texture; harder to pull through tight weaves

Six-strand cotton floss comes in skeins of 8 m (about 8.7 yd). Separate the strands one at a time and lay them back together for a smoother line.

What herringbone stitch is used for

It makes a decorative band, so it shows up on borders, tea towel and apron hems, and over the seams of a crazy quilt where two patches meet. A band of crosses reads well from a distance and frames a block or a label neatly.

Packed closely, it becomes a filling. Worked closed on the back of a sheer fabric, it is the basis of shadow work: the color shows softly through the cloth, and the front looks like two lines of backstitch.

Thread and needle

Six-strand floss works well, and the strands table above shows the choices. Two or three strands give a light, lacy band. Four to six strands make a heavier border, which suits wider bands where the long slants need body.

Use an embroidery (crewel) needle with a sharp point for the stitching. If you plan to lace a second thread through the finished band, switch to a blunt tapestry needle for that part so it slides under the stitches without piercing them; see hand sewing needle sizes.

Spacing, tension and common mistakes

Draw both guide lines before you start. Herringbone is all about even spacing, and lines make that easy. On an evenweave fabric you can count threads instead. Notice that you move left to right along the band, but on each line the needle takes its small bite pointing back to the left, as steps 2 and 3 show.

Let the long slants rest on the fabric. Pulled tight, they draw the two lines toward each other and the band puckers. A hoop helps a lot here.

  • Bites of different sizes: the crosses land in different places and the band looks uneven. Keep each small stitch the same length.
  • Skipping a line: every stitch alternates top, bottom, top, bottom.
  • Needle pointing the wrong way: if it points right, the threads will not cross.

Herringbone vs. similar stitches

Herringbone and feather stitch both zigzag along a line, but feather stitch loops the thread under the needle so each branch is caught at the bottom, while herringbone just crosses one straight stitch over the next. Blanket stitch is another band stitch, with straight uprights joined along one edge.

If you need a single line rather than a band, use stem stitch or split stitch.

Working curves and corners

Herringbone is happiest on straight bands and gentle curves. For a curve, draw both guide lines first and keep them the same distance apart; take slightly shorter steps along the inner line and slightly longer ones along the outer line so the crosses fan evenly.

For a square border, stop the band at each corner and start the next side fresh, or plan the corner on paper so the last cross lands on the turn.

Variations

Closed herringbone moves each new stitch right up against the last, so there are no gaps and the band becomes solid. Double herringbone adds a second row in another color, set between the crosses of the first. Laced herringbone weaves a separate thread under the slants without piercing the fabric.

Questions

Which direction do you work herringbone stitch?

Usually left to right along the band, with each small bite on the guide lines taken from right to left.

How far apart should the two lines be?

It is up to you. Narrow bands look neat and tight; wide ones look open and need more strands so the long slants do not look thin.

What is closed herringbone stitch?

The same stitch with no gaps between the small bites. Worked on the back of sheer fabric, it is used for shadow work.

Why is my herringbone puckering?

The thread is pulled too tight. Let each slant rest on the fabric and use a hoop.

How we calculate: every rule and rounding step is on our method page; where the sizes and facts come from is on sources.

Traditional stitch. Step diagrams drawn by broiderer.com.

broiderer.com is not affiliated with any fabric, thread or sewing machine brand. Last reviewed November 2026.