Skip to content
broiderer

Embroidery stitches

Embroidery hoop sizes

Type the width and height of your design and how much fabric you want beyond the hoop. You get the smallest common hoop that fits, the design's corner-to-corner size and the square of fabric to cut.

Published Nov 7, 2026

Your numbers

runs in your browser, nothing is saved

Hoop
6 in
Design corner to corner5 in
Fabric to cut10 × 10 in

Worked example

  1. A rectangle fits inside a circle when the circle is wider than its diagonal: √(4² + 3²) = 5 in
  2. Leave about ½ in clear inside the ring on each side: 5 + 1 = 6 in
  3. Smallest common hoop that size or bigger: 6 in
  4. Fabric: hoop + 2 in on every side to grip and tighten

Common hand embroidery hoop sizes

HoopLargest square designLargest 4:3 designFabric to cut (2 in extra)
3 in1⅜ × 1⅜ in1⅝ × 1¼ in7 × 7 in
4 in2⅛ × 2⅛ in2⅜ × 1¾ in8 × 8 in
5 in2⅞ × 2⅞ in3¼ × 2⅜ in9 × 9 in
6 in3½ × 3½ in4 × 3 in10 × 10 in
7 in4¼ × 4¼ in4¾ × 3⅝ in11 × 11 in
8 in5 × 5 in5⅝ × 4¼ in12 × 12 in
10 in6⅜ × 6⅜ in7¼ × 5⅜ in14 × 14 in
12 in7¾ × 7¾ in8¾ × 6⅝ in16 × 16 in

Hoops from 4 to 6 in are the usual sizes to start with; above about 12 in a hoop gets heavy and the fabric sags.

Why the diagonal decides the hoop

A hoop is round and most designs are rectangles. The rectangle fits only when its corners clear the ring, so the measurement that counts is the diagonal, not the width. For a 4 × 3 in design the diagonal is √(4² + 3²) = 5 in. The calculator then leaves about ½ in clear inside the ring on each side, which brings it to 6 in. That room keeps your needle and hand off the edge of the ring while you stitch the corners.

Another example with the same rule: a 3 × 2 in design has a diagonal of about 3.6 in, plus 1 in is 4.6 in, so a 5 in hoop fits it and you cut a 9 × 9 in piece of fabric.

Common hoop sizes

Hand embroidery hoops are commonly sold in 3, 4, 5, 6, 7, 8, 10 and 12 in diameters, and those are the sizes the calculator picks from. Hoops from 4 to 6 in are the usual sizes to start with: big enough for a small motif, small enough to hold in one hand for a long time. Above about 12 in a hoop gets heavy and the fabric tends to sag in the middle.

If your design falls between two sizes, take the larger hoop. Squeezing a design into a hoop where the corners sit under the ring makes those corners hard to stitch.

How much fabric to cut

The fabric needs to reach past the hoop on every side so you can grip it and pull it tight. The calculator adds 2 in on each side by default, which is why a 6 in hoop takes a 10 × 10 in square. Sources give anywhere from 1 to 5 in, so raise it if you plan to frame the piece or lace it over a board; you need spare fabric to wrap around the back.

For counted work, the cross stitch calculator works out the design size from the stitch count and the aida cloth count, and then you can come back here for the hoop.

Using the hoop well

A hoop has an inner ring and an outer ring with a screw. Loosen the screw, lay the fabric over the inner ring, press the outer ring down over it and tighten a little at a time, easing the fabric until it is smooth and taut, without pulling the grain out of line. Snug is enough; cranking the screw hard is a common cause of hoop marks.

Take the fabric out of the hoop at the end of each stitching session. Left in for days, the rings can leave a crease that is hard to press out, especially on light fabrics. For first stitches to practice in a small hoop, try the stem stitch or split stitch.

Questions

What size embroidery hoop should a beginner buy?

A hoop from 4 to 6 in is the usual starting size. It holds a small design and is comfortable to hold in one hand.

Does the design have to fit inside the hoop?

It is easiest if it does, with about ½ in to spare on each side, so you can reach the corners.

How do I measure an embroidery hoop?

Hoops are sold by their diameter, so a 6 in hoop is about 6 in across. Measure your design's diagonal and add about 1 in to choose one.

Why does my fabric go loose in the hoop?

Fabric relaxes as you work. Pull it gently taut around the edge and tighten the screw a little; check it every so often while you stitch.

How we calculate: every rule and rounding step is on our method page; where the sizes and facts come from is on sources.

broiderer.com is not affiliated with any fabric, thread or sewing machine brand. Last reviewed November 2026.