Skip to content
broiderer

Embroidery stitches

Split stitch

Split stitch is a line stitch where the needle comes up through the middle of the previous stitch and splits its strands, so each stitch locks into the last. The numbered diagrams below show it step by step.

Published Nov 14, 2026

  1. 12

    01Come up at 1 and go down at 2, one stitch length along the line.

  2. 3

    02Come up at 3 through the middle of that stitch, splitting the strands of floss in two.

  3. 34

    03Go down at 4, one stitch length ahead. Use an even number of strands so the split is clean.

  4. 04Repeat. The line looks like a tiny chain and makes a good outline or a base for padded satin stitch.

Key:stitches already madethis stepneedle under the fabric (dashed)

How many strands of floss

StrandsLine it makes
1 strandvery fine lines, lettering, small details
2 strandsfine outlines; the usual choice on 14 count fabric
3 strandsmedium lines, most surface embroidery
4 to 6 strandsbold lines and texture; harder to pull through tight weaves

Six-strand cotton floss comes in skeins of 8 m (about 8.7 yd). Separate the strands one at a time and lay them back together for a smoother line.

What split stitch is used for

It makes a smooth, solid outline that hugs curves, which is why many stitchers reach for it for lettering, outlines and fine details. It is also the standard first step before satin stitch: outline the shape in split stitch, then work the satin stitches over that edge. The split stitch line holds the satin edge crisp and raises it slightly.

Rows worked close together fill a shape, too. In medieval English church embroidery, known as Opus Anglicanum, split stitch was the main stitch, and the faces were worked in very fine rows of it that followed the shape of the cheeks and chin.

Thread and needle

Split stitch needs a thread you can divide, and six-strand cotton floss is ideal. Use an even number of strands, as step 3 says, so the needle can split them evenly: two strands for a fine outline, four for a bolder line. If you only have an odd number, split through the center strand. The strands table above shows how the line weight changes.

Use a sharp embroidery (crewel) needle so it pierces the floss cleanly; a blunt tip tends to slide to one side. Hand sewing needle sizes lists the sizes, and a hoop from embroidery hoop sizes keeps the stitches even.

Tension and common mistakes

Keep the pull gentle and even. A hard tug drags the split apart and puckers the fabric; a loose stitch leaves a loop that sits above its neighbors.

  • Missing the center: if the needle comes up beside the stitch instead of through it, you have made a stem-like stitch, not a split stitch. Look at the floss as you come up.
  • Long stitches: the line turns jagged on curves. Short, even stitches give the smoothest line.
  • Odd strand counts split off-center: one side of each stitch looks thinner. Switch to an even count.
  • Twisted floss: let the needle hang now and then so the strands untwist and lie flat.

Split stitch vs. similar stitches

Stem stitch comes up halfway along the last stitch too, but beside it, so the line twists into a rope. Split stitch comes up through it, so the line is flatter and looks a little like a fine chain. It is not a chain stitch, though: no loop is formed.

For a broad decorative band rather than a line, look at herringbone stitch or feather stitch.

Working curves and corners

Curves are where split stitch shines. Shorten the stitches as the curve tightens; the tighter the bend, the shorter they should be. Because every stitch is pinned by the next, the line does not drift outward the way a long backstitch can.

At a sharp corner, end one stitch right at the point, then start the new side with a stitch that comes up through the end of that last stitch. The corner stays crisp and connected.

Variations

Split backstitch reverses the direction: you bring the needle down through the previous stitch from the front instead of up from below. On the front it looks much the same. Rows of split stitch laid side by side make a smooth filling that can follow any shape,.

Questions

How many strands of floss should I use for split stitch?

An even number, usually two or four, so the needle can divide them equally. With an odd number, split through the middle strand.

Is split stitch the same as stem stitch?

No. In stem stitch the needle comes up beside the previous stitch, giving a twisted rope. In split stitch it comes up through the middle of the floss, giving a flatter line.

Why use split stitch under satin stitch?

It gives the satin stitches a firm, slightly raised edge to cover, so the outline stays sharp and smooth.

How we calculate: every rule and rounding step is on our method page; where the sizes and facts come from is on sources.

Traditional stitch. Step diagrams drawn by broiderer.com.

broiderer.com is not affiliated with any fabric, thread or sewing machine brand. Last reviewed November 2026.